FeatherClock 1.4.0

This repo contains code written for the Adafruit Feather HUZZAH ESP32 (hence the name) and the Raspberry Pi Pico W, all running MicroPython. The Feather board requires the addition of female headers.

The clock uses the Adafruit FeatherWing four-digit, seven-segment LED add-on — or any other HT16K33-based segment LED for that matter. You’ll want a non-FeatherWing display if you’re assembling a Pico W, for which you’re free to select any of its I2C pins. The Feather/FeatherWing combo requires specific pins, but the display assembly fits directly on top of the MCU board into a single, convenient unit. This is the version I use, for this very reason.

This code is an attempt to replicate my Electric Imp clock project. Currently, the clock has no remote control, which the Electric Imp Platform makes very easy to implement, but is rather less so here. You can set preferences, though. Adding a web UI, served locally or remotely, lies in a future phase of the project.

Note I previously supported the Adafruit Feather HUZZAH ESP8266, but this is no longer the case: its RTC is poor and it has too little memory. If you are using this board, you can find the original, un-updated code in the archive directory. I will instead be focusing on boards that are more modern.

New Features

Version 1.4.0 includes the option to alternate the clock with a readout of the current outdoor temperature. This requires the prefs.json file to be updated with additional keys, and this has been done with the sample file included here (see Clock Settings, below). It is easy to turn off this feature if you don’t require it: change the value of the show_temp key to false, or comment out the line. By default, the clock will not enable this feature.

The temperature is collected from Open Meteo, which provides free access for low-volume, non-commercial applications. The code contains a basic Open Meteo integration class, which can be extracted and used elsewhere.

Version 1.4.0 of featherclock also includes the option to alternate the clock with a readout of the current day of the month and the month. This requires the prefs.json file to be updated with additional keys, and this has been done with the sample file included here (see Clock Settings, below). It is easy to turn off this feature if you don’t require it: change the value of the show_date key to false, or comment out the line. By default, the clock will show the date.

Installation

Pre-requisites

For ESP32 boards

1. Install pyboard.py from GitHub.
   • Copy pyboard.py to a location accessible via your $PATH. Rename it pyboard.
2. Install esptool.py using brew install esptool

For Pico W boards

1. Install pyboard.py from GitHub.
   • Copy pyboard.py to a location accessible via your $PATH. Rename it pyboard.
2. Download MicroPython and drop the .uf2 file onto the mounted RP2 drive.

App Installation

Pre-requisites

1. Set up a Python virtual environment
   1. git clone https://github.com/smittytone/FeatherClock
   2. cd FeatherClock
   3. python -m venv .python
   4. source .python/bin/activate
   5. pip3 install -r requirements.txt
   6. Continue as below. Once complete, run deactivate

For ESP32 boards

1. Connect your assembled FeatherClock (Feather plus LED add-on).
2. Run ls /dev/cu* (macOS) or ls /dev/ttyAM* (Linux)
   • Note the Feather’s device file path.
3. Update/install MicroPython: 1. esptool.py --chip esp32 --port <FEATHER_DEVICE_PATH> erase_flash 1. esptool.py --chip esp32 --port <FEATHER_DEVICE_PATH> --baud 460800 write_flash -z 0x1000 ESP32_GENERIC-20241129-v1.24.1.bin
4. cd featherclock
5. Run ./install.sh <FEATHER_DEVICE_PATH>
6. Press 3 for an ESP32 device.
7. Enter your WiFi SSID.
8. Enter your WiFi password.
9. After the code has copied, power-cycle your FeatherClock or press the RESET button.

For Pico W boards

1. Connect your assembled FeatherClock (Pico W plus HT16K33-based LED).
2. Run ls /dev/cu* (macOS) or ls /dev/ttyAM* (Linux)
   • Note the Pico’s device file path.
3. Update/install MicroPython:
   • Copy across (for example) RPI_PICO_W-20250415-v1.25.0.uf2
4. cd featherclock
5. Run ./install.sh <FEATHER_DEVICE_PATH>
6. Press W for a Pico W.
7. Enter your WiFi SSID.
8. Enter your WiFi password.
9. After the code has copied, power-cycle your FeatherClock.

Clock Settings

For now, the clock’s prefs are set by sending over a prefs.json file with the following values:

{ "mode":   <true/false>,       # 24-hour (true) or 12-hour (false)
  "colon":  <true/false>,       # Show a colon between the hours and minutes readouts
  "flash":  <true/false>,       # Flash the colon symbol, if it's shown
  "bright": 10,                 # Display brightness from 1 (dim) to 15 (bright)
  "bst":    <true/false>,       # Auto-adjust for Daylight Saving Time
  "do_log": <true/false>,       # Write log data to the file `log.txt` on the device
  "show_date": <true/false>,    # Alternate clock with day and month readout
  "show_temp": <true/false>,    # Alternate clock with outside temperature
  "lat": float,                 # Your location, in latitude and longitude
  "lng": float
}

Having installed pyboard.py as above, you send over prefs file using:

pyboard.py -d <FEATHER_DEVICE_PATH> -f cp prefs.json :prefs.json

However, the install.sh script does this for you, and allows you to enter your WiFi credentials

To get <FEATHER_DEVICE_PATH>, you can add my Z Shell function dlist() to your .zshrc file. After restarting your terminal, you can run:

./install.sh $(dlist)

To Do

• Web UI for clock settings control.

Release History

• 1.4.0 18 July 2025
  • Add local temperature readout to alternate with clock readout.
  • Add day and month readout to alternate with the clock readout (and temperature readout, if enabled).
  • Minimise MicroPython display memory allocations.
  • Bring the project up to date.
• 1.3.0 24 January 2023
  • Add experimental Trinkey RP2040 version.
  • Better resilience to WiFi connection loss.
  • Better log file management.
  • Update to latest HT16K33 drivers.
  • Archive ESP8266 version.
• 1.2.3 23 February 2022
  • Better help in install.sh
  • Device-side errors now issued to log file.
  • Correct pyboard instructions.
• 1.2.2 5 February 2022
  • Style install script errors.
  • Update esptool.py installation instructions.
  • Add dlist() link.
  • No application code changes.
• 1.2.1 13 September 2021
  • Clarify installation instructions for ESP32 and ESP8266 boards.
  • Update install script.
  • No application code changes.
• 1.2.0 26 August 2021
  • Fix for post time-check pauses
  • Update install.sh to use MicroPython’s pyboard.py.
  • Update install.sh to copy prefs.json over if it is present in the working directory.
• 1.1.0 3 December 2020
  • Revised code.
  • Matrix display version.
• 1.0.10 19 November 2020
  • Adds Feather Huzzah 32 version.
• 1.0.9 29 September 2020
  • Improve RTC time checks.
  • Improve installation script.
• 1.0.8 6 September 2019
  • Add installation script.
• 1.0.7 25 April 2019
  • Add optional on-device JSON prefs (prefs.json) loading.
• 1.0.6 13 April 2019
  • Add app preferences structure.
• 1.0.5 10 April 2019
  • Correct the months used for BST checking.
• 1.0.4 9 April 2019
  • Various linting-suggested code improvements.
• 1.0.3 8 April 2019
  • Improve RTC updates by making NTP checks.
• 1.0.2 — 5 April 2019
  • Add regular RTC updates.
• 1.0.1 4 April 2019
  • Add disconnection indicator to display.
  • Correct constant usage.
• 1.0.0 3 April 2019
  • Initial release.

Licence

FeatherClock is copyright 2025, Tony Smith. It is released under the MIT licence.