I own ge concord express sw version 0500 and a new home automation module.
wired in the automation unit.
powered up both.
see on auto unit the power led on and the blinking BUSS red LED. So auto unit looks good.
PROBLEM: The Concord shows no indication of recognizing the automation unit. The panel should be beeping with a unknown new device. It is not.
I run the concord232server in debug mode and get:
2020-11-13 21:32:49,391 _internal INFO * Running on http://0.0.0.0:5007/ (Press CTRL+C to quit)
2020-11-13 21:32:49,861 concord DEBUG Sending message (retry=1) '022022'
2020-11-13 21:33:09,399 concord DEBUG Looping 20
2020-11-13 21:33:29,439 concord DEBUG Looping 40
2020-11-13 21:33:49,477 concord DEBUG Looping 60
2020-11-13 21:34:09,516 concord DEBUG Looping 80
^[[4~^[[1~^[[1~^[[1~^[[1~^[[1~^[[1~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~2020-11-13 21:34:29,554 concord DEBUG Looping 100
2020-11-13 21:34:49,592 concord DEBUG Looping 120
2020-11-13 21:35:09,632 concord DEBUG Looping 140
2020-11-13 21:35:29,670 concord DEBUG Looping 160
2020-11-13 21:35:49,708 concord DEBUG Looping 180
2020-11-13 21:36:09,747 concord DEBUG Looping 200
2020-11-13 21:36:29,786 concord DEBUG Looping 220
2020-11-13 21:36:49,830 concord DEBUG Looping 240
2020-11-13 21:37:09,873 concord DEBUG Looping 260
2020-11-13 21:37:29,917 concord DEBUG Looping 280
2020-11-13 21:37:49,959 concord DEBUG Looping 300
2020-11-13 21:38:10,002 concord DEBUG Looping 320
2020-11-1
I then plug the serial (usb) cable into miniterm and send a
ControlJ 020204 command and get a hex 6 form the auto unit. This is the unit replying with an ACK.
It appears that the concord alarm is just not seeing the auto panel.
Anyone have ideas?
Thank you.
I own ge concord express sw version 0500 and a new home automation module.
wired in the automation unit.
powered up both.
see on auto unit the power led on and the blinking BUSS red LED. So auto unit looks good.
PROBLEM: The Concord shows no indication of recognizing the automation unit. The panel should be beeping with a unknown new device. It is not.
I run the concord232server in debug mode and get:
2020-11-13 21:32:49,391 _internal INFO * Running on http://0.0.0.0:5007/ (Press CTRL+C to quit)
2020-11-13 21:32:49,861 concord DEBUG Sending message (retry=1) '022022'
2020-11-13 21:33:09,399 concord DEBUG Looping 20
2020-11-13 21:33:29,439 concord DEBUG Looping 40
2020-11-13 21:33:49,477 concord DEBUG Looping 60
2020-11-13 21:34:09,516 concord DEBUG Looping 80
^[[4~^[[1~^[[1~^[[1~^[[1~^[[1~^[[1~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~^[[5~2020-11-13 21:34:29,554 concord DEBUG Looping 100
2020-11-13 21:34:49,592 concord DEBUG Looping 120
2020-11-13 21:35:09,632 concord DEBUG Looping 140
2020-11-13 21:35:29,670 concord DEBUG Looping 160
2020-11-13 21:35:49,708 concord DEBUG Looping 180
2020-11-13 21:36:09,747 concord DEBUG Looping 200
2020-11-13 21:36:29,786 concord DEBUG Looping 220
2020-11-13 21:36:49,830 concord DEBUG Looping 240
2020-11-13 21:37:09,873 concord DEBUG Looping 260
2020-11-13 21:37:29,917 concord DEBUG Looping 280
2020-11-13 21:37:49,959 concord DEBUG Looping 300
2020-11-13 21:38:10,002 concord DEBUG Looping 320
2020-11-1
I then plug the serial (usb) cable into miniterm and send a
ControlJ 020204 command and get a hex 6 form the auto unit. This is the unit replying with an ACK.
It appears that the concord alarm is just not seeing the auto panel.
Anyone have ideas?
Thank you.